Landscaping

Gravel Calculator

Calculate gravel volume for one or more rectangular project areas using measured depth and an adjustable waste allowance, without assuming material density.

Last reviewed: November 11, 2026

Project measurements

Measurement system

This calculator reports volume only. Material density, weight, compaction, and pricing are not assumed.

Gravel area 1

How to use this calculator

  1. Choose US customary or metric measurements.
  2. Enter the length, width, and installed depth for each gravel area.
  3. Add differently sized areas separately.
  4. Set a waste allowance and calculate volume.

How the calculation works

The calculator multiplies each rectangular area by its depth, combines the volumes, and then applies the selected waste allowance. It reports volume only because gravel weight depends on material density and moisture.

Formula

Section volume = length × width × depth
Adjusted volume = combined volume × (1 + waste % ÷ 100)
Cubic yards = cubic feet ÷ 27

Worked example

A 10 ft × 5 ft area at 6 in deep contains 25 cubic feet. With 10% waste, the planning volume is 27.5 cubic feet, or about 1.02 cubic yards.

What a few inches of depth does

Depth is the biggest lever on a gravel order. The table is arithmetic on 100 square feet; scale it to your own area.

DepthCubic feet per 100 sq ftCubic yards per 100 sq ft
2 in16.670.62
3 in25.000.93
4 in33.331.23
6 in50.001.85

A second example with two areas

A 30 ft by 3 ft path at 3 in deep is 22.5 cubic feet. An 8 ft by 8 ft pad at 4 in deep is 21.33 cubic feet. Together that is 43.83 cubic feet. With 10% waste it is 48.22 cubic feet, or 1.79 cubic yards.

Volume, weight, and what suppliers sell

Many suppliers sell gravel by the ton, but this calculator gives volume. To convert, ask the supplier for the weight per cubic yard of the product you want, then multiply. As an illustration only, if a product were quoted at 1.4 tons per cubic yard, 1.79 cubic yards would be 2.5 tons. Your supplier's figure will differ by material and moisture.

Common mistakes

  • Using loose depth when the plan gives compacted depth. Compaction reduces thickness, so the amount to order is larger than the finished volume.
  • Forgetting that a thin layer over a large area is a large number. A 2 in layer on 1,000 square feet is 166.67 cubic feet, or 6.17 cubic yards.
  • Ordering by the visible footprint and missing the extra width a base needs beyond the finished edge.
  • Ignoring the difference between decorative gravel, drainage stone, and base material. The right product for the job comes from your plan, not from this tool.

Reading the result

The result is in cubic feet, cubic yards, and cubic meters. Cubic yards is the unit most US suppliers use for bulk loads, and it is also the unit to compare against tons once your supplier gives you a conversion. If you enter the weight per cubic yard in the optional field, the page also shows tons.

Before ordering, compare the result with a quick estimate you can do in your head: area in square feet times depth in inches, divided by 324. For the 10 ft by 5 ft area at 6 in deep, that is 50 times 6 divided by 324, or 0.93 cubic yards, which matches the 25 cubic feet shown above before waste.

Project considerations

  • Use compacted or installed depth if that is what the project requires.
  • Density, weight, compaction, and delivery quantities vary by product and are not inferred.
  • Confirm actual ordering increments with the supplier.

Frequently asked questions

Why is tonnage optional?

Converting volume to weight requires a material-specific density, and no single density fits every product. Enter your supplier’s tons per cubic yard in the optional field to see tons.

Can I combine a path and patio?

Yes. Add each rectangular area separately and use its own dimensions and depth.

Should I order the exact result?

Compaction, uneven ground, and edges usually call for an allowance. The waste field is where you set it.