Roofing

Roof Pitch Calculator

Calculate objective roof geometry from rise and run, including pitch per 12 inches, slope percentage, and angle in degrees.

Last reviewed: November 11, 2026

Project measurements

Enter rise and run in the same unit. The result is geometric only and is not structural or safety guidance.

Vertical change
Horizontal distance

How to use this calculator

  1. Measure the vertical rise and horizontal run using the same unit.
  2. Enter both values.
  3. Calculate to see pitch per 12 units, slope percentage, and angle.

How the calculation works

Pitch per 12 scales the rise-to-run ratio to a 12-unit run. Slope percentage is rise divided by run times 100. The angle is the arctangent of rise divided by run.

Formula

Pitch = (rise ÷ run) × 12
Slope % = (rise ÷ run) × 100
Angle = arctan(rise ÷ run)

Worked example

A rise of 6 and run of 12 produces a 6:12 pitch, a 50% slope, and an angle of approximately 26.6°.

Common pitches at a glance

Every value is computed from rise over run. The roof-surface multiplier tells you how much larger the sloped roof is than the footprint it covers.

PitchSlopeAngleSurface multiplier
3:1225%14.04 degrees1.031
4:1233.3%18.43 degrees1.054
6:1250%26.57 degrees1.118
8:1266.7%33.69 degrees1.202
12:12100%45.00 degrees1.414

A second example: measuring from the attic

If the ridge is 4 ft above the top plate and the horizontal run is 10 ft, the pitch is 4 / 10 x 12 = 4.8:12, the slope is 40%, and the angle is 21.80 degrees. A 1,500 square foot footprint at 6:12 has about 1,677 square feet of roof surface (1,500 x 1.118), before overhangs and waste.

Measuring safely

Measure rise and run from the attic framing or with a level and tape from a safe position. Use the same unit for both numbers; mixing inches and feet is the most common error. Roof access carries a real fall risk, so use ladders properly and consider a professional for steep roofs.

Pitch, slope, and angle

Pitch is usually written as rise per 12 inches of run, slope as a percentage, and angle in degrees. They describe the same line. A 12:12 roof is 45 degrees and a 100% slope.

Using pitch for materials

Pitch matters to material quantities because a steeper roof has more surface than the building footprint beneath it. The surface multiplier in the table is the number to apply to a footprint area: a 4:12 roof has 5.4% more surface than the plan, and a 12:12 roof has 41.4% more. Roofing squares, shingle bundles, and underlayment are all counted on the sloped surface, not on the footprint.

Measure from inside when you can, and use the same unit for rise and run.

Checking a pitch in the field

A simple way to measure pitch is with a 12 inch level and a tape. Hold the level horizontally against the underside of a rafter, mark 12 inches along it, and measure straight up to the rafter at that point. That number of inches is the pitch. If it reads 6 inches, the roof is 6:12. Repeat in two or three places, because old framing can sag or twist and a single reading can mislead.

You can also work from a gable end by measuring the height of the peak above the eave line and half the building width, then entering those as rise and run. For example, a peak 8 ft above the eave line on a 24 ft wide building has a rise of 8 and a run of 12, which is 8:12.

Project considerations

  • Use matching units for rise and run.
  • This calculation describes geometry only.
  • Roof access is hazardous; use safe measurement methods and qualified help when needed.

Frequently asked questions

What does a 6:12 pitch mean?

The roof rises 6 units for every 12 units of horizontal run.

Is roof pitch the same as roof angle?

They describe the same slope differently. Pitch is a rise-to-run ratio, while angle is measured in degrees.