Concrete & Masonry

Brick Calculator

Calculate approximate brick quantities from wall area, openings, brick dimensions, mortar joint thickness, and waste allowance.

Last reviewed: November 11, 2026

Project measurements

Measurement system

Quantities use the entered unit face plus mortar joint as the repeating module. This is not structural or code guidance.

Total measured area of doors, windows, and other full openings.

How to use this calculator

  1. Choose US customary or metric measurements.
  2. Enter wall dimensions and the combined area of openings.
  3. Enter the brick face dimensions and mortar joint thickness.
  4. Apply waste and calculate the rounded purchase quantity.

How the calculation works

The calculator subtracts openings from wall area and divides the remainder by the repeating brick-and-joint module. Waste is applied before rounding upward.

Formula

Net wall area = length × height − openings
Brick module = (brick length + joint) × (brick height + joint)
Purchase quantity = net area ÷ module area × waste factor, rounded up

Worked example

For 100 ft² with no openings, a 7.625 in × 2.25 in brick and 0.375 in joint uses an 8 in × 2.625 in module. The base estimate is about 685.7 bricks; with 10% waste, purchase 755.

How joint thickness changes the count

The module is the brick face plus a joint on each dimension. The table uses a 7.625 in by 2.25 in brick on 100 square feet.

JointModuleBricks per 100 sq ft
0.25 in7.875 x 2.5 in731.4
0.375 in8 x 2.625 in685.7
0.5 in8.125 x 2.75 in644.5

A second example: a garden wall

A 24 ft by 8 ft wall is 192 square feet. With the same brick and 0.375 in joint, that is 1,316.6 bricks before waste. With 10% waste it is 1,448.2, so 1,449 bricks. A wall built two bricks thick, a double wythe, needs about twice as many, since the calculator counts only one face.

Check the brick size

Brick sizes differ by product, and the example brick is one of several. A 7.625 x 2.625 in brick with a 0.375 in joint has a 24 square inch module, which is 600 per 100 square feet. Enter the face size from your product data sheet.

Mortar and cuts

Cuts around openings and at corners produce partial bricks that are rarely reused fully, so the waste percentage is a judgment. Mortar is not included.

Counting for a wall that is more than one brick thick

This calculator counts the face of the wall, so it gives the number of bricks in one layer, called a wythe. A wall that is two wythes thick needs about double the count. Walls with a cavity or a veneer over a backup wall use bricks only on the outer layer, so they use the single count.

To estimate mortar, you need the joint volume, which depends on the brick depth and how the bricks are laid. The calculator does not estimate it, so use the manufacturer’s mortar guidance for your brick and joint.

Ordering and storing bricks

Bricks are usually sold in cubes or on pallets with a stated count, so convert your result to the packaging count rather than ordering a loose number. Ask the supplier whether the count assumes the same size and color range, and try to order everything for the wall at once, since a second order can differ slightly in shade.

Keep a small reserve of the same lot after the wall is built. Repairs years later are much easier when the replacement bricks match.

Project considerations

  • Enter face dimensions as laid in the wall.
  • Brick sizes and joint profiles vary, so edit the defaults.
  • Corners, patterns, cuts, and detailing can affect actual quantities.

Frequently asked questions

Does this calculate mortar?

No. It uses joint thickness only to estimate the repeating brick module.

Why is the final number rounded up?

Bricks are purchased as whole units, so a fractional calculated quantity cannot satisfy the measured area.