Flooring guide

How Many Tiles Do I Need?

Divide area by tile size, add a layout-based allowance for cuts, and round up to whole tiles and boxes, with a worked bathroom example.

Last reviewed: November 11, 2026

The short answer

Divide the area to be tiled by the area of one tile, then add an allowance for cuts and breakage and round up to whole tiles or whole boxes. The tile size, the layout, and the box size drive the answer more than any other input.

Use the Tile Calculator

Why tile counts surprise people

Floor area is easy to measure. Turning it into a tile count is where mistakes happen, because tile size changes the answer dramatically. The same 100 square feet takes 900 tiles of 4 inch by 4 inch, 400 of 6 by 6, 100 of 12 by 12, and just 25 of 24 by 24. Mixing up a single dimension in inches can leave you off by a large factor.

Tile is also sold in boxes with a fixed count or coverage, and boxes from different production lots can vary slightly in shade. That makes it worth buying all you need at once, along with a few spares for repairs.

Work out the count

  1. Measure the area

    Break the space into rectangles, multiply length by width for each, and add them. Subtract only areas that will not be tiled, such as a tub or a built-in.

  2. Find one tile’s area

    Multiply the tile’s length and width, in the same unit as your area. Use the actual size on the product label, which may differ from the nominal size.

  3. Divide

    Total area divided by tile area gives the tiles you would need with no cuts and no loss.

  4. Add the allowance

    Multiply by 1 plus the allowance. A simple square layout needs less than a diagonal or herringbone layout, which creates more cut pieces.

  5. Round up to boxes

    Divide by the number of tiles per box and round up.

Tile count formulas

Tile area (ft²) = tile length (in) × tile width (in) ÷ 144
Tiles = project area ÷ tile area
Purchase = tiles × (1 + allowance % ÷ 100), rounded up
Boxes = purchase tiles ÷ tiles per box, rounded up

There are 144 square inches in a square foot, so dividing by 144 converts square inches to square feet.

Worked example: a bathroom floor in large tiles

The floor is 8 ft by 10 ft. The tile is 12 inches by 24 inches. The layout is a straight pattern with a 12% allowance. Each box holds 8 tiles.

  1. Area: 8 × 10 = 80 ft²
  2. Tile area: 12 × 24 ÷ 144 = 2.00 ft²
  3. Tiles with no waste: 80 ÷ 2 = 40
  4. With 12%: 40 × 1.12 = 44.8, so 45 tiles
  5. Boxes: 45 ÷ 8 = 5.63, so 6 boxes, or 48 tiles

Result: Six boxes cover the project and leave 3 spare tiles beyond the 45 planned, and 8 beyond the 40 that go on the floor.

Large tiles and layout

Large tiles have fewer joints, but a single awkward row can force you to cut many tiles. The layout matters more than the formula. Before ordering, sketch the room with tiles drawn to scale, starting from a centerline or from the most visible wall. Count whole tiles and cut tiles separately. If the last row would be a sliver, shift the starting line.

A pattern with an offset or a diagonal creates triangles at the walls, and each cut can produce a piece that is not reusable. This is why the allowance rises for those layouts. The size of the increase is a planning choice, so ask your installer what they use for your pattern.

Grout joints and the face dimension

The calculation above uses the tile’s face size. In reality each tile occupies a little more, because of the grout joint. A 12 inch tile with a 1/8 inch joint repeats every 12.125 inches. Over a long run that adds up to more than a whole row, but for most rooms the difference is smaller than the allowance you add. If you want to be precise, enter the tile plus joint as the dimension.

Joint width and tile spacing come from the tile maker’s instructions and the installer. The calculator does not specify them.

Before you order

Check the box
Boxes list the number of tiles and the square feet. Use whichever your calculation produces and confirm both.
Buy spares
Tile lots can differ in shade, so keep a few extra from the same lot for future repairs.
Look at the substrate
Tile needs a suitable surface. Leveling and preparation are separate work and cost.
Include thresholds and edges
Edge pieces, trim, and transitions are sold separately from field tile.

Counting walls, backsplashes, and showers

The same method works on walls. Measure each wall as a rectangle, subtract the window, niche, or fixture it surrounds, and divide by the tile area. A backsplash 10 ft long and 18 inches high is 15 square feet. With 3 inch by 6 inch tiles (0.125 square foot each) that is 120 tiles before the allowance, which shows how quickly small tiles add up.

Wall tile is often cut around outlets, windows, and corners, so the allowance is usually higher than for a simple floor. Keep the floor and wall quantities separate, because they often use different tile and different boxes.

Matching boxes to your count

Box labels list the number of tiles and the coverage in square feet. They should agree for the tile size, but nominal sizes can make the coverage differ slightly from your own arithmetic. Use the box’s own figures when you convert, and keep the tile size on the label for your records.

If you are mixing sizes in a pattern, calculate each size separately with its own share of the area. A border of small tile around a field of large tile needs two counts.

Tile questions

How many extra tiles should I buy?

It depends on the layout and the tile. A straight layout in a simple rectangle needs less than a diagonal layout or a room with many corners. Use the allowance your installer recommends.

Should I measure in inches or feet?

Either, as long as you convert. The calculator accepts both and handles the conversion.